Le revêtement de film optique est composé d'un milieu en couches minces , un type de matériau de milieu optique qui propage le faisceau lumineux à travers l'interface. L'application des films optiques a commencé dans les années 1930. Les films optiques modernes ont été largement utilisés dans le domaine de l'optique et de la technologie optoélectronique, dans la fabrication de divers instruments optiques.

The main optical thin film devices include reflective film, anti-reflection film, polarizing film, interference filter and beam splitter, etc. They have been widely used in the construction of the national economy and national defense, and have received increasing attention from scientific and technical workers. For example, the use of anti-reflection films can reduce the luminous flux loss of complex optical lenses by ten times; the use of high reflectance mirrors can double the output power of the laser; the use of optical films can improve the efficiency and stability of silicon photovoltaic cells Sex.

1. Structure

Le modèle de film optique le plus simple est une couche mince avec une surface lisse et un milieu homogène isotrope. Dans ce cas, la théorie de l'interférence optique peut être utilisée pour étudier les propriétés optiques des films optiques. Lorsqu'une onde plane monochromatique est incidente sur le film optique, de multiples réflexions et réfractions se produisent sur ses deux surfaces. Les directions de la lumière réfléchie et de la lumière réfractée sont données par les lois de la réflexion et de la réfraction, et les amplitudes de la lumière réfléchie et réfractée La taille est déterminée par la formule de Fresnel

2. Caractéristiques

Les caractéristiques du film optique sont: la surface est lisse, l'interface entre les couches de film est géométriquement divisée; l'indice de réfraction de la couche de film peut changer à l'interface, mais il est continu à l'intérieur de la couche de film; ça peut être un support transparent ou ça peut être

Optical film

Absorbing medium; can be uniformly normal or non-uniformly normal. The actual applied film is much more complicated than the ideal film. This is because: during preparation, the optical and physical properties of the film deviate from the bulk material, and its surface and interface are rough, resulting in diffuse scattering of the light beam; the interpenetration between the film layers forms a diffusion interface; due to the growth of the film layer , Structure, stress and other reasons, the anisotropy of the film is formed; the film layer has a complex time effect.

Filter introduction:

Used to select the optical device of the required radiation band. A common feature of filters is that no filter can make the image of a celestial body brighter, because all filters absorb certain wavelengths, which makes objects darker.

Filter principle:

The filter is made of plastic or glass and then added with special dyes. The red filter can only let red light through, and so on. The transmittance of the glass sheet is originally similar to that of air, and all colored light can pass through, so it is transparent, but after dyeing, the molecular structure changes, the refractive index also changes, and the passage of certain colored light changes. For example, a beam of white light passes through a blue filter and emits a beam of blue light, while green light and red light are very few, and most of them are absorbed by the filter.

One, anti-reflection film

Also called antireflection coating, its main function is to reduce or eliminate the reflected light from optical surfaces such as lenses, prisms, and plane mirrors, thereby increasing the light transmission of these components and reducing or eliminating stray light from the system.

Second, the optical film

Le film antireflet est le film optique de sortie le plus largement utilisé et le plus grand. Par conséquent, il s'agit toujours d'un sujet de recherche important dans la technologie des films optiques. L'objectif de la recherche est de trouver de nouveaux matériaux, de concevoir de nouveaux systèmes de films et d'améliorer le processus de dépôt. Il utilise le moins de couches, le processus le plus simple et le plus stable pour obtenir le rendement le plus élevé possible et obtenir les résultats les plus idéaux. Pour le film mince laser, le film antireflet est le maillon faible des dommages du laser, et comment augmenter sa force de destruction est également l'un des problèmes qui préoccupent le plus les gens.

Trois, film réfléchissant

Sa fonction est d'augmenter la réflectivité de la surface optique. Les films réfléchissants peuvent être généralement divisés en deux catégories, l'un est un film réfléchissant métallique et l'autre est un film réfléchissant tout diélectrique. De plus, il existe des films réfléchissants diélectriques métalliques qui combinent les deux.

Quatre, filtre d'interférence

It is a type of optical film with the most variety and complicated structure. Its main function is to split the spectral band. The most common interference filters are cut-off filters and band-pass filters. The cut-off filter can divide the considered spectrum into two parts, one part does not allow light to pass (called the cut-off region), and the other part requires light to pass through (called the band-pass region). According to the position of the passband in the spectral region, it can be divided into two kinds of long-wave pass and short-wave pass. Their simplest structures are respectively, where H and L represent thick high and low refractive index layers, and m is the number of periods. The film system having the above structure is called a symmetric periodic film system. If the considered spectral region is wide or the passband transmittance ripple requirements are high, the film structure will be more complicated.

Five, spectroscopic film

According to certain requirements and certain methods, the light beam is divided into two parts. The beam splitting film mainly includes wavelength splitting film, light intensity splitting film and polarizing beam splitting film.

The wavelength splitting film is also called two-color splitting film. As the name implies, it is a film that divides the light beam into two parts according to the wavelength region. This film can be a cut-off filter or a band-pass filter. The difference is that the wavelength splitting film must consider not only transmitted light but also reflected light. Both require a certain shape of the spectral curve. The wavelength splitting film is usually used at a certain angle of incidence. In this case, the spectral curve will be distorted due to the influence of polarization. In order to overcome this effect, the problem of depolarization of the film must be considered.

The polarization beam splitting film is made by utilizing the polarization effect of the film when the light is incident obliquely. The polarization beam splitting film can be divided into two types, a prism type and a flat plate type. The prismatic polarizing film utilizes the polarization effect of the interface when Brewster angle is incident. When the light beam always enters the interface of two materials at Brewster's angle, no matter how many thin film layers there are, the reflected light of the horizontal vibration is always zero, and the light of the vertical component vibration increases with the number of thin film layers. Increased, as long as the number of layers is sufficient, the transmitted light beam can be basically vibrated in the parallel direction, and the reflected beam is basically light that is vibrated in the vertical direction, so as to achieve the purpose of polarized beam splitting. The Brewster angle at the interface of the thin film material, so the film must be plated on the prism, then the incident medium is not air but glass. The flat-type polarizing film is mainly made of the difference in the bandwidth of the reflection bands of the two polarized components of the dielectric reflective film when obliquely incident. In general high-reflection films, as the incident angle increases, the reflection bandwidth of the vertical component gradually increases, and the bandwidth of the parallel component gradually decreases. Selecting the high reflection area of ​​the vertical component and the high transmission area of ​​the parallel component as the working area can form a polarizing film that reflects the vertical component through the parallel component. The incident angle of this polarizing film is generally selected near the Brewster angle of the substrate . The working wavelength range of the prism-type polarizing film is relatively wide, and the degree of polarization can also be made relatively high, but its preparation is cumbersome, difficult to make large, and the laser resistance is relatively low. The wavelength range of flat polarizers is relatively narrow, but it can be made very large and the laser resistance is relatively high, so it is often used in strong laser systems.